Skip to content

Industry

Invar and Super Invar Machining for Photonics and Laser Systems

Send your resonator, mount or enclosure drawing and we quote the finished parts and place the work with a partner shop that cuts the low-expansion alloys and can hold the geometry a laser system needs.

1.2 to 1.6 ppm/°CTypical Invar 36 CTE near room temperature
0.3 to 0.6 ppm/°CTypical Super Invar CTE over a narrow band
One itemised quotePartner shops price your drawing and you receive one quote for the finished parts
24 business hoursTypical response time on a submitted RFQ

Why Optics, Photonics & Laser Systems programs specify these alloys

A laser resonator or cavity spacer only performs if the distance and angle between its optical elements hold steady as temperature changes. Invar 36 and Super Invar exist for exactly this problem, but the alloy choice is only half the specification. The machining sequence, the stress relief cycle and the inspection method decide whether a part actually keeps the geometry the alloy was chosen to protect.

Photonics and laser programs bring their own version of this problem: a production run that needs the same part fifty times over, a temperature-stabilized enclosure where the alloy choice depends on the actual duty cycle rather than the steady-state set point, and a scale-up path from a hand-built prototype to a documented, qualified process.

This page is a starting point. We hold no certification ourselves. What we do is take your drawing, place it with a partner shop that has relevant experience in the low-expansion alloys, and send you one itemised quote.

Where Optics, Photonics & Laser Systems uses Invar, Kovar and Alloy 42

Laser resonator housings and cavity spacers

Parallelism between mirror faces, bore concentricity and cavity length, protected by a rough, stress relieve, finish sequence.

Cavity spacers and mirror mounts for production laser systems

Repeatability across a run, not just a single precise part, plus alignment that survives shipping and handling.

Temperature-stabilized photonics enclosures

Reference lengths and mount positions inside a TEC or oven-controlled housing, where Super Invar may or may not be justified.

Optical benches and structural frames

Multi-element mounting plates that hold several optics in a fixed relative position through ambient swings.

What to put on the RFQ, and what to vet in a supplier

We quote the finished parts and answer for them. Your program still sets its own qualification rules, so state them on the RFQ. These lines get you a quote that covers them and a shop that can answer the qualification questions your program asks.

  1. State the operating and any transient temperature range the part actually sees, not just the steady-state set point.

  2. Call out parallelism, concentricity and flatness explicitly, not just linear dimensions.

  3. Specify the stress relief and any stabilization cycle, or require the shop to document a fixed one.

  4. State inspection temperature and soak time, and whether a CMM report is required.

  5. Note your production stage (prototype, pilot or production) and expected volume.

  6. Flag whether second-source qualification is planned so the first shop documents a reproducible process.

Optics, Photonics & Laser Systems guides

All guides

Alloy pages: Invar 36 machining, Super Invar machining, Kovar machining, Alloy 42 machining. Spec numbers and CTE by temperature band on the Invar specs reference.

Have a drawing ready?

Send the short version now. We will ask for anything missing. For full details up front use the full RFQ form. Reply within 24 business hours.

Your files go only to the partner shops we ask to price the part. Ask for an NDA and nothing is shared until it is signed.

STEP, IGES, PDF, DWG or DXF. Can't upload from your phone? Email the files to sales@invarmachining.com after you send this form.
Reply within 24 business hours.

Questions from Optics, Photonics & Laser Systems buyers

Something else? Email .

Who manufactures the parts?

Partner shops in our network machine the parts, and you deal with us for the quote, the order, delivery and any remake. Remake terms are confirmed on your quote.

Are the partner shops certified?

We do not hold or verify certifications ourselves, and we never claim a shop is certified on its behalf. If a certification matters to your program, tell us on the RFQ and we ask the shop for the certificate before the work is placed.

Should I specify Invar 36 or Super Invar for a photonics enclosure?

Run the growth calculation for your actual duty cycle, including any power-up transient, against your alignment budget. Invar 36 is adequate for most designs. Super Invar is worth its longer lead time only when Invar 36 falls short.

Can one shop handle both my prototype and later production volume?

Sometimes, but confirm the shop can document a fixed process and run a pilot batch before committing volume. A shop good at fast prototypes is not automatically set up for repeatable batch production.

How fast will I hear back after submitting an RFQ?

Within 24 business hours, with one itemised quote or a clear no.

Get a quote